First time the sound BEEPDRAM refresh failure. Have problems accessing the system memory to merefreshnya.2 TimesParity string of failures. In the data transmitted in the computer, usually added parity bit which is used for detecting and correcting errors. This work was carried out a series of parity on the computer. This is probably caused by a problem with memory or motherboard.3 TimesBase 64K memory failure. Base 64K memory is 64 MB of memory on the RAM first. This failure could be due to the memory slots are grouped into modules that have a defective chip.4 timesThe failure of the system timer. There might be an error on one or more timers that are used to control functions on the motherboard.5 aProcessor failure. Can be caused by excessive heat, or because the processor is not installed properly into the socket.6 TimesThe failure of the keyboard controller / gate A20. The keyboard controller is a chip on the motherboard that mengedalikan your keyboard.7 TimesProcessor errors.8 TimesError read / write memory display.9 TimesDamage to the BIOS.10 TimesCMOS error.11 TimesDamage to the cache memory.
AWARD BIOSAward prefer messages through the monitor. But there are times when video card is not working and the message is displayed using the beep code. Therefore, the BIOS beep code on this type less. BIOS beep codes at this as a sign Morse, combining long and short beeps.1 long beepProblem with memory. Chances are that memory is not installed correctly, or faulty memory chips as well. Could be related to damage to the motherboard.1 long beep, 2 short beepsVideo system error. BIOS can not access the video system to write error messages to the screen. There are several possibilities, including video cards are installed on the existing system on-board video card, or use an IRQ that is already in use for the video card is causing the conflict. Alternatively, the video card is not installed properly.1 long beep, 3 short beepsSame as above, there is an error in the video. BIOS can not access the video system to display an error message to display. Beep connect connectCan be caused by a memory or video card. There are some general guidelines that can be used for any BIOS. These general guidelines can only be used for errors detected before and during the Power On Self Test (POST). We already know the procedure performed when starting the computer is turned on, and this will be helpful in diagnosing the problem. The first time when the computer is turned on, the power supply will send power to all components. When switched on when there is no any reaction, then check the internal power supply located on your computer. To test this, we can use LED (Light Emiting Diode) and then plug the POWER LED on the connector. If the flame, means the power supply is still good. Then, if all components have got enough power, the processor will work to find instructions. He will find these instructions in the ROM BIOS. For processors, the possibility is that excess heat caused by overclocking or not the position perfect. For the BIOS, it is unlikely that the location of the BIOS chip is not perfect. Check the BIOS can be done on another computer. Some viruses can already damage the BIOS program. If the POST will continue but not completed, most likely the problem is on the motherboard. For this one, there are several steps that must be done:If the PC will not boot at all, ensure minimal components are mounted, ie the processor, memory filled with appropriate video card, and a drive, and make sure all components are properly installed. Components are soldered onto there should be nomissing.Remove the components that are not mandatory, such as expansion cards, external peripherals such as printers, scanners and others, due to improper installation can cause the I / O error. Then turn on the system, and try to plug one by one card to test it.Double-check the jumper settings on the motherboard. Make sure the processor type, bus speed, multiplier, and voltage jumpers. And also make sure the BIOS jumper is in proper position.Change the BIOS settings to the default settings to ensure the problem does not lie in the BIOS settings are redundant. For example by lowering the read / write access time of memory and hard disk. Check all cable connections on the motherboard are correct. Check whether there are components that have excess heat. If there is, change the BIOS settings and the settings are lower.
HandlingFor cases 1, 2, and 3 times the beep, try to correct the first memory position. If it still happens, there is the possibility of faulty memory. Replace with new memory. For 4, 5, 7 and 10 times the beep, the motherboard is damaged and must be repaired or replaced. To 6 times a beep, try to correct the position of the keyboard controller chip. If there are errors, replace the keyboard chip. 8 kai beep indicates a memory error on the video adapter. Replace the video card. 9 times beep indicates the failure of the BIOS chip. Usually not due to a position less than perfect. 11 times the beep, replace the cache memory.
